DXF 2S 7.4V 5200mAh Lipo Battery 120C Hard Case Battery with Deans Plug for 1/8

DX 2S Lipo Battery 7.4V 5200mAh 50C Battery with DEANS/T Plug Hard Case for 1/8 1/10 RC Vehicles Car Slash RC Buggy Truggy RC Airplane(2 Pack) About DXF: DXF is one battery brand of Shenzhen SKT Technology Co., Ltd Company founded in 2016, is a leading manufacturer of RC LiPo Battery based on Shenzhen China.DXF Batteries offer an excellent value by providing factory direct pricing and quality that meets or exceeds that of other major battery manufacturers. All of DXF batteries comply with RoHS and CE quality testing standards.DXF only use Grade A cell. DXF which is the Fans hobbyking town. DXF will support you ultimate experience service. Key Point: – Stable automatic stacking technology enables single-cell capacities . – Higher capacity during heavy discharge. More than 90% at 100% C rate. – Fast charge capable, up to 5C on some batteries. – Longer Cycle Life, almost double that of standard lipoly technology. – Friendly after-sales support and after-sales guarantee. Features: 【2S 5200mAh Specification】- Battery voltage: 7.4V; Configuration: 2S1P; Cell voltage: 3.2~4.2V; Capacity: 5200mAh; Discharge: 50C; Plug: deans/t Connector. 【2S Lipo Dimensions】- DXF 5200mAh 2S lipo dimension is: 138*47*25mm/5.43*1.85*0.98inch; Approx Weight: 250g/8.82oz. 【7.4V RC Lipo Application】 – DXF 2S 5200mAh Lipo battery compatible with 1/8 and 1/10 rc car, Losi, HPI Strada XB 1/10 RTR Electric Buggy, Team Associated, Axial, Emaxx, Bandit, Rustler version(Only if the voltage, dimension and the plug match, then it will fit). 【Safety Warning】- 1. Users must read safety manual before use of the battery; 2. You must use Lithium Polymer(LiPo) specific balance charger only; 3. The charge rate should not exceed 1C; 4. Never charge the battery unattended. PackageList: 2PCS 100% new 7.4V 5200mah 120C lipo HardCase with DEANS plug OR Caution: Don’t over charge more than 4.2V and dont over discharge below 3.7V Don’t put it beside the high temperature condition. Don’t throw it into fire. Don’t throw it into water. Easy way to check your lipo battery Capacity of currently status : Note: if you need some custom Plug, you could order the battery and make a note whichPlug you need. Warm Reminder: 1. Before using it, please full charge it with specific lipo balance charger; 2. Charge lipo battery no more than 4.20V per cell. As for battery pack in series, Please choose balance charging mode or charge each cell respectively; 3. Charging temperature must range in 15-35 Celsius, reverse charging is prohibited; 4. The voltage difference between any two cells should be in 0.03V, or charge is advised to balance the voltages beforeusage; 5. Please make sure the cut-off voltage is not lower than 3.4V, we highly recommend not lower than 3.6V; 6. Never discharge battery with current over the designed maximum continuous discharging current. After over current discharge, the performance will be deteriorated and cycle life will be shortened, causing overheating and even welling ,breakage, internal short-circuited etc; 7. If the surface temperature exceeds 65 Celsius while functioning, the battery should be suspended using until it cool down to ambient temperature naturally. Higher temperature may result int battery swelling and performance; 8. Do regularly charge discharge for maintenance(about 1-3 times every 3 months),battery must stored at about 3.85v/cell; 9. Do store battery at a place with low-humidity and free from corrosive gas within the temperature ranged from -20 Celsius to +40 Celsius 10. Under any circumstances dis-assembly of battery is prohibited.